Weider Home Gym Manual 9628
. PATENT PENDING WELDER USER'S MANUAL Model No. 831.159360 Serial No. The serial number can be found in the location shown below. Write the serial number in the space above. Serial Number Decal F' E: R i., E: Eq3, HELPLINEI 1-800-736-6879 aAUTION- SEARS.
TABLE OF CONTENTS IMPORTANT PRECAUTIONS. BEFORE YOU BEGIN.ASSEMBLY.ADJUSTMENT. TROUBLE-SHOOTING AND MAINTENANCE.CABLE DIAGRAM.ORDERING REPLACEMENT PARTS.Back Cover FULL 90 DAY WARRANTY.Back Cover Note: An EXPLODED DRAWING/PART LIST and a PART IDENTIFICATION CHART are attached to the center of this manual, Remove the EXPLODED DRAWING/PART LIST and the PART IDENTIFICATION CHART before beginning assembly. WELDER= system, the PRO 9625 will help you to achieve the specific results you want.
Find best value and selection for your Weider Pro 9628 Home Gym search on eBay. World's leading marketplace.
PRO 9625 (see the front cover of this manual). ASSEMBLY Before beginning assembly, carefully read the.
As you assemble the home gym system, be sure following Information and Instructions:' that all parts are oriented as shown in the drawings. Place all parts of the home gym system in a cleared area and remove the packing materials. Press a 2' Square Inner Cap (27)into the Rear Upright (56), h Side of Bracket Attach a Rubber Bumper (90) to the Rear Upright (56) with a #8 x 112'Tap Screw (89). Slide the Rear Llpright (56) onto the 5/16' x 2 1/2'. Set two Weight Bumpers (19) onto the bracket Drilled holes must on the Stabilizer (5).
Insert both Weight Guides be at the top through the Weight Bumpers and the bracket on the Stabilizer. Be sure that the drilled holes In the Weight Guides are at the top, as shown.
Attach the upper ends of the Weight Guides (62) to the Top Frame (55) with the 5/16' x 6' Bolt (60), two 1/2' x 3/4' Spacers (61), and a 5/16' Nylon Locknut (3). Tighten all Nylon Locknute used In steps 2 through 6. Lubricate both axles on the Top Frame (55), Slide the Right Arm (48) onto the right axle. Note: Be careful not to confuse the Right Arm with the Left Arm (47); refer to step 11 to Identify the Right Arm.
Be sure that the upper end of the Right Arm is behind the indicated bracket on the Top Frame (55). During steps 15 through 36, refer to the CABLE DIAGRAM on page 23 of this manual to verify proper cable routing. Before begin- ' -86 (174') ning this section, identify the Long Cable (86), the Medium Cable (23), and the Short Cable (58) by comparing the lengths and ends of the cables. Route the Medium Cable (23) around the =V- Pulley (6) on the Right Arm (48). Be sure that the Cable Is In the groove of the 'V'- Pulley and that the Long Cable Trap (50) Is turned to hold the Cable In place, '13ghten the 3/8'.
Wrap the Medium Cable (23) around a 3 1/2' Pulley (15). Attach the Pulley to the Top Frame (55) with a 3/8' x 1 3/4' Bolt (87) and.a 3/8' on Locknu t (21) ii ¸¸!!i!i 22. Attach the end of the Short Cable (58) to the Long 'U'-Bracket (57) with a 1/4' Nylon Lock- nut (2) and a 1/4' Flat Washer (10). Do not completely tighten the Nylon Locknut.
It should be threaded onto the end of the Cable so only a couple of threads are showing above the nut, as shown In the Inset drawlng. Locate the Long Cable (86).
Route the Long Cable under the 3 1/2' Low Pulley (88). Be sure that the end of the Cable with the ball!i!!! i!ii I!
Is on the Indicated side of the Press Frame (17) and that the Cable Is between the Pulley and the crossbar on the Press Frame. Wrap the Long Cable (86) around a 3 1/2' i!il ¸¸ Pulley (15). Attach the Pulley and a Cable Trap (66) to the Press Frame (17) with a 3/8' x 3 1/2' Bolt (16), a 3/8' Flat Washer (9), and ¸%1¸¸¸¸¸i a 3/8'.
Route the Long Cable (86) around the indicat- ed 3 1/2' Pulley (15) and through the Long 'U'-Bracket (57). The Cable must be between the Cable Trap (66) and the Pulley.
'Rghten 3/8' x 2' Bolt (12) and the 3/B' Nylon Locknut (not shown). Press a 1 3/4' Square Inner Cap (44) into the Rear Seat Frame (77). Insert the 1/4' x 2 112'Carriage Bolt (91) into the center hole in a Seat Plate (37). Attach the Seat Plate to a Seat (13) with two 1/4' x i i!iiii!i! Press a 1 1/2' Square Inner Cap (32) into the Front Seat Frame (36). Insert the 1/4' x 2 1/4' Carriage Bolt (38) into ii i!i the center hole in a Seat Plate (37). Attach the Seat Plate to the Seat (13) with two 1/4' x i!iiii ii 112'Screws (18).
Insert the other Pad Tube (28) into the Leg Lever (29). Slide a Foam Pad (30) onto each end of the Pad Tube. Remove the backing from the PRO 9625 decal and apply it to the home gym system as shown. ADJUSTMENT The instructions below describe how each part of the home gym system can be adjusted. Refer to the exercise poster accompanying this manual to see how the home gym system should be set up for each exercise.
IMPORTANT: When attaching the lat bar or nylon strap, make sure that the attachments are In the cor- rect starting position for the exercise to be performed. ATrACHING THE LEG LEVER TO THE LOW PULLEY STATION To use the Leg Lever (29), the seat must be attached to the front upright (see ATTACHING AND REMOV- ING THE SEATS below).
Weider 265 Home Gym Manual
Attach one end of the Chain (52) to the Long Cable (86) with a Cable Clip (53). WEIGHT RESISTANCE CHART This chart shows the approximate weight resistance at each station. 'Top' refers to the 6.5 lb. The other numbars refer to the 12.5 lb. Weight plates. Weight resistance shown for the butterfly arm station is for each butterfly arm. TROUBLE-SHOOTING AND MAINTENANCE inspect and tighten all parts each time you use the home gym system.
Weider Pro 9628 Home Gym Manual
Replace any worn parts immediately. The home gym system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. 23 1 67 TIGHTENING THE CABLES Woven cable, the type of cable used on the home. CABLE DIAGRAM The cable diagram below shows the proper routing of the Short Cable (58), the Medium Cable (23), and the Long Cable (86). Use the diagram to be sure that the three cables and the cable traps have been assembled correctly. PART LISTmModel No.
831.159360 Ros96A Part Part Qty. Description Qty. Description 100291 5/16' x 2 1/2' Carriage Bolt 120733 1' Round Inner Cap 012139 1/4' Nylon Locknut 132812 Long Cable Trap Rear Base 012056 5/16' Nylon Locknut 196 Front Base 116868 Chain 132797. EXPLODED DRAWING-Model No. 831.1 59360 ' 6 86. ' -'.-.
' -78 21 21- i 75.' '-' 12'6 1'5. SEARS The model number and serial number of your WEIDEFP PRO 9625 Model No. 631.159360 are listed on a decal attached to the frame.
See the front cover of this manual to find the location of the decal. All replacement parts are available for immediate purchase or QUESTIONS? Special order when you visit your nearest SEARS Service Center.
No interest if paid in full within 18 months To avoid interest, you must pay the full promo balance before the promo period ends. If you do not, we will charge interest from the purchase date at the standard Purchase APR. After the promo period ends, the standard APR also applies to the remaining balance and the charged interest.
You are required to make minimum payments, but minimum payments will not pay off the balance on time. You must make larger payments to avoid the interest. Advertised monthly payment, if any, is greater than your required minimum monthly payment and excludes taxes, delivery or other charges. Limited Time Offer. Regular account terms apply to non-promo purchases. Minimum interest charge: $1. Standard Purchase APR: 29.99%.
Prior purchases excluded. Account must be in good standing. Subject to credit approval.