Lt 1000 Service Manual
. SATELLITE TRACER LT-1000 Model SERVICE MANUAL May 2006 Pages in total: 38 LLT8.RDA001A/E. NIDEK CO., LTD.: 34-14, Maehama, Hiroishi-cho, Gamagori, Aichi 443-0038, Japan (Manufacturer) Telephone: (0533) 67-6611 Facsimile: (0533) 67-6610 NIDEK CO., LTD: 6th Floor, Takahashi Bldg., No.2, 3-chome, Kanda-jinboucho (Tokyo Office) Chiyoda-ku, Tokyo 101-0051, Japan Telephone: (03) 3288-0571 Facsimile: (03) 3288-0570 Telex: 2226647 NIDEK J NIDEK INCORPORATED: 47651 Westinghouse Drive, Fremont, California 94539, U. 2.2 During Service.2-1 § 3 TROUBLESHOOTING.3-1 § 4 SUB TROUBLESHOOTING.4-1 4.1 The LT-1000 does not Start.4-1 4.2 The Color LCD Display is Abnormal.4-2 4.2.1 The back light does not light up.
4-2 4.3 The Touch Panel is not Operational. § 7 ADJUSTMENT.7-1 7.1 Touch Panel Calibration. 7-1 7.2 Tracing Unit Calibration. 7-1 7.2.1 Calibration with standard frames.7-1 7.2.2 Calibration with standard pattern.7-2 7.2.3 Torque calibration. 7-3 7.2.4 Full calibration.7-3 7.3 Displaying Parameter Setting Screen. LLT8A.RDA001A/E § 1 INTRODUCTION. This service manual is for the SATELLITE TRACER LT-1000.
See 'TO LEVEL MOWER HOUSING' in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trimming. • Drive so that clippings are discharged onto the area that has been cut. Sep 8, 2018 - Document for Craftsman Lt1000 Lawn Tractor Manual is available in. 107,rover 620 tdi repair manual,yamaha g9 a service manual,2004. EBooks Craftsman Riding Lawn Mower Manual Lt1000 is available in formats. Mower operating guides and service manuals craftsman riding mower lt1000.
It does not include technical information for preparing lenses. This manual is thoroughly understood before servicing. Refer to the SATELLITE TRACER LT-1000 Operator’s Manual and Parts List.
Craftsman Lt 1000 Service Manual Pdf
LLT8A.RDA001A/E 1 - 2. After part replacement, check that all parts are fixed in their original positions securely. If the LT-1000 produces smoke or strange odors, immediately turn the power off and disconnect the electrical plug from the outlet. Usage of the instrument under such abnormal conditions may cause fire or electric shock. LLT8A.RDA001A/E 2 - 2. Plug the power cord in the wall outlet and turn the power switch on.
Does the LT-1000 start? 4.1 The LT-1000 does not start. Is the color LCD display normal? 4.2 The color LCD display is abnormal. Is the LT-1000 touch panel operational? 4.3 The touch panel is not operational. LLT8A.RDA001A/E 3 - 2.
LLT8A.RDA001A/E § 4 SUBTROUBLESHOOTING 4.1 The LT-1000 does not Start. Is the voltage from the wall outlet within the Use a wall outlet which meets the specifications. (100 V and 200 V systems: ±10%) Are the fuses blown? Replace the fuses (9). LLT8A.RDA001A/E 4.2 The Color LCD Display is Abnormal. Does the back light light up? 4.2.1 The back light does not light up.
Is there a break in the LCD cable (42203-E018)? Chevrolet suburban owners manual. Replace the LCD cable (42203-E018). Replace the color LCD module (40273-E020). Replace the BA01 board (43401-BA01). LLT8A.RDA001A/E 4.3 The Touch Panel is not Operational. Is touch panel calibration possible?
Is the symptom improved? I s t h e s i d e p l a t e ( 4 3 4 0 1 - M 0 0 4 ) grounded to the casing by the CA12 Ｎo cable (43401-CA12) and CA13 cable. LLT8A.RDA001A/E 4.4 The Main Screen is not Displayed on the Color LCD.
Does the inserted CF card contain the application Insert a CF card containing the application files files (It8aautoload.bin and It8aautoload.txt)? (It8aautoload.bin and It8aautoload.txt).
Replace the BA01 board (43401-BA01). (Refer to 6.7.2.) Ｎo Use a different CF card on which the application. LLT8A.RDA001A/E 4.5.1 Initialization does not start.
Is the voltage between the P204 (J4) 1st and 6th Replace the BA02 board (43401-BA02). Pins on the BA02 board (43401-BA02) DC + 24 (Refer to 6.7.3.) V? At this time, P204 is not connected. Is there a break in the CA06 cable (43401-CA06)? Replace the CA06 cable (43401-CA06). LLT8A.RDA001A/E 4.5.3 No traced data is displayed.
Is there a break in the CA06 cable (43401-CA06)? Replace the CA06 cable (43401-CA06). Is there a break in the CA07 cable (43401-CA07)? Replace the CA07 cable (43401-CA07). Are the DIP switches of the tracer ASSY.
(43401- Set the DIP switches of the tracer ASSY. LLT8A.RDA001A/E § 5 REMOVING PROCEDURE 5.1 Top Cover ASSY. Unscrew SB3 × 6 (n = 4).
Disconnect the P501 (J1) connector from the BA05 board (43401-BA05). Remove the top cover ASSY. Reassemble the removed parts in reverse order.
LLT8A.RDA001A/E 5.3 LCD Rear Cover 1. Unccrew PC3 × 6. Remove the CF card slot cover (43401-M309). Unscrew PC3 × 6 (n = 4). Remove the LCD rear cover (43401-M307).
Reassemble the removed parts in reverse order. LLT8A.RDA001A/E § 6 REPLACEMENT PROCEDURE 6.1 Tracer ASSY. Replacement part: 1. Remove the top cover ASSY. (Refer to 5.1.) 2. Disconnect all connectors. Unscrew SB4 × 6 (n = 2) and SB4 × 8 (n = 2).
LLT8A.RDA001A/E 6.3 Cable Assembly Replacement part: 41971-CA07 1. Remove the tracer ASSY. (Refer to 6.1.) 2. Disconnect the CN6P connector.
Unscrew SB4 × 22 (n = 4) to replace the cable assembly (41971-CA07). Reassemble the removed parts in reverse order. LLT8A.RDA001A/E 6.6 Inverter Replacement part: 42203-E017 1. Remove the LCD rear cover (43401-M307). (Refer to 5.3.) 2. Disconnect the CN2 connector from the color LCD module (40273-E020) and the CN1 connector from the inverter (42203-E017). Unscrew PC2.6 × 4 (n = 2) to replace the inverter (42203-E017).
LLT8A.RDA001A/E 6.7.3 BA02 board Replacement part: 43401-BA02 1. Replace the switching power supply (80602- 00104). (Refer to 6.2.) 2.
Disconnect the P201 (J1), P202 (J2), P203 (J3), and P204 (J4) connectors from the BA02 board (43401-BA02). Unscrew the four attached screws. LLT8A.RDA001A/E 6.7.5 BA03 board Replacement part: 43501-BA03 1.
Remove the tracer ASSY. (Refer to 6.1.) 2.
Disconnect the P301 (J1) connector from the BA03 board (43501-BA03). Unscrew FK2.6 × 4 (n = 2) to replace the BA03 board (43501-BA03). LLT8A.RDA001A/E 6 - 6. § 7 ADJUSTMENT 7.1 Touch Panel Calibration 1. Push the touch panel calibration button on the rear side of the LT-1000 with a pencil point or such (φ6).
Turn the power on while pressing the button. A red square is first displayed in the upper- left corner of the screen as shown to the right. LLT8A.RDA001A/E 5. Check the traced data (circumference) on the Circumference layout screen. Perform calibration again with the standard frames when the circumference is not in the range of 162.83 ±0.05 mm. Remove the standard frames. 7.2.2 Calibration with standard pattern 1.
LLT8A.RDA001A/E 7.2.3 Torque calibration 1. Turn the power on while simultaneously pressing the right-eye and left-eye tracing buttons. Confirm that the LED of the both-eye tracing button blinks. Open the upper and lower sliders fully. Press the both-eye tracing button while holding the sliders open.
One short beep sounds when calibration is successfully completed. Multiple beeps sound should calibration fail. The cause may be that the measured data or LT-1000 operation is in error. Check the inside of the tracer. LLT8A.RDA001A/E 7.3 Displaying Parameter Setting Screen 1.
Press the MENU button on the layout screen. The pop-up menu is displayed. Pressing the Setting button. Select the screen Setting that includes the desired parameters. System Setting Network Adjustment Communication Maintenance 7 - 5. Prepare the LT8AAUTOLOAD.BIN and LT8AAUTOLOAD.TXT files of the desired version and overwrite them in the CF card. Insert the CF card and close the CF card slot cover (43401-M309).
Turn the power on. Check the software version after the LT-1000 software starts. LLT8A.RDA001A/E § 8 INFORMATION 8.1 Wiring Diagram 8 - 1. LLT8A.RDA001A/E 8.2 Appearance Front view LCD panel Pattern setting unit Tracing unit Tracing unit cover Touch pen 8 - 2. LLT8A.RDA001A/E Rear view CF card slot cover Power switch Inlet Fuse holder USB memory slot Barcode scanner connector LAN connector RS-232C connector Tracing unit Upper slider Rim clip Pattern tracing pin Stylus Rim clip Lower slider Pattern setting unit support Right-eye tracing button Both-eye tracing button Left-eye tracing button. LLT8A.RDA001A/E 8.3 Labels 8 - 4.
Cancel the error in the host PC. 8.5 Factory Setting of Tracing Unit Spacifications Machine Mode Protocol ID No.
LT-1000 LT-1000 Meganet off-off-on-off. SW1 off-off-on-off: Communication rate 38400 bps off-off-off-off: Communication rate 9600 bps. SW2 on: The power is supplied from the first communication port (when the communication adapter is used). LLT8A.RDA001A/E 8.6 Parameter Setting Table Screen Parameter name Factory setting Setting range ENGLISH Language ENGLISH is fixed. PTN Memory INTERNAL INTERNAL/EXTERNAL JOB# Input Interface KEYPAD TENKEY/KEYPAD PTN# Input Interface KEYPAD TENKEY/KEYPAD System Setting 1 Trace Data Auto Set ON/OFF VCA Data Display Rx/A,B VCA Layout Display NORMAL. LLT8A.RDA001A/E § 9 SUPPLEMENT 9.1 Abbreviation for Screws 9 - 1. LLT8A.RDA001A/E 9 - 2.
Cub Cadet lawn care equipment has been built to last through the harshest of weather conditions. They are a leader in building smart outdoor power equipment with advancements that make their products better, and provide a better user experience. Cub Cadet equipment is award-winning. The list goes on and on, but a few of our favorites are the CES Innovation Award, Consumer's Digest Best Buy Distinctions, and Popular Mechanics Breakthrough Award. Below we've added a selection of service manuals for some of the most popular Cub Cadet mowers, tractors, zero-turns and snow blowers.
These manuals are for reference purposes only - once you are ready to purchase, please either type the exact part number in the search box above, or click the 'Parts Lookup' tab above to use our advance. If you are looking for, you can click to view a selection we've posted.